Any TP-Link wireless router or adapter comes with a licensed disk with a proprietary utility for Windows in the box, with which you can connect to the Internet and set up wifi distribution on your PC. By and large, it is not needed, since it is easy to set all the necessary configurations in the admin panel through a regular browser, as we have already seen. However, since such a possibility exists, why not figure out how to use the Windows utility for routers or TP-Link adapters? Let's see where to download it, how to install and configure the router using the TP-Link utility.
Let me make a reservation right away, so that there is no confusion, that in this article we will talk about two different TP-Link utilities. One is used to configure wifi routers. The other is for wireless adapters for PCs.
Where can I download the TP-Link utility for PC on Windows?
Connecting a TP-Link router to the Internet through a special utility makes sense if you do not need any subtle refinements in the network parameters. For quick setup, it’s easier and more convenient to use a step-by-step program that will tell you what to do.
The same applies to the WiFi adapter. All the necessary software to connect your PC to the Internet is already available in Windows. However, the proprietary utility makes this process easier in some aspects/
If you have a new router or TP-Link wifi adapter that comes with a branded CD, then you just need to insert it into the computer drive and install the “Setup Wizard” utility. If it is not there, then you can download it from the official website in the “Support” section.
Here you need to enter your model number in the search field, for example “TL-WR740N”. A page will open with an image of the corresponding TP-Link router or adapter. We need to go to the “Support” section in the additional menu
And then select the hardware version (revision) of your model from the drop-down list.
You can recognize it from the sticker located on the bottom cover of the device. The revision is designated as “Rev.1.0” or “Ver. 1.0"
On this page, switch to the “Utility” tab
And download the TP-Link “Easy Setup Assistant” program file to your computer
Download firmware for the router
To download the firmware for TP-LINK TL-WR1045ND you just need to carefully read the page you are currently on. Don't forget to leave your reviews (the form for adding reviews is at the bottom of the page). If you don't mind, you can share the link to the firmware with your friends. Also, if you have not found the answer to your question, you can ask it using the form at the bottom of the site.
Here you will find the latest drivers for wireless devices. To download the new driver, you need to follow the “Download firmware” link, which is located just below.
| Russian Internet providers | Ukrainian Internet providers |
|
|
Video instructions on how to set up TP-LINK TL-WR1045ND
Installing the utility on Windows and connecting the TP-Link router
Since the Windows utility is universal for different TP-Link rotary models, first you need to select yours from the list
Next, select the language
and follow the detailed instructions.
- We connect the router to the computer using a patch cord - one end to the network port of the PC, the other to the LAN connector of the router. It is usually highlighted in yellow
- We connect the router with an Internet cable, which we insert into the WAN connector - it is marked blue
- We turn on the router to the power grid
- Checking the operation of the light indicators on the case
- We are waiting for the router to connect to the computer
Next, you need to select the type of Internet connection. You need to find out which one is right for you from the provider’s contract.
What is your opinion: is WiFi harmful?
Yes
22.92%
No
77.08%
Voted: 36462
Open source for programmers (GPL)
The following information is intended for programmers and is not relevant to most end users of TP-Link products.
TP-Link products contain code developed by third parties, including code developed under the GNU General Public License (GPL) version 1/version 2/version 3 or the GNU Lesser General Public License (LGPL). You may use the corresponding software under the terms of the GPL license.
You can view, print and download the relevant GPL license terms here. The GPL Source Center provides you with downloadable GPL source code for the relevant software used in TP-Link products, as well as other information, including a list of TP-Link software that contains GPL source code.
WiFi setup
Next, set a name for your home wireless network, which will be displayed in the list of connections on computers and gadgets. Don't leave it as standard for safety reasons.
After this, select the encryption type and set your created login and password for the connection. The most reliable one today is WPA2/PSK, choose it.
If everything went well, the last window will notify you about this:
Unfortunately, the TP-Link configuration utility does not have a simulator, like the web interface. Therefore, it will not be possible to practice “on cats” in advance. But as you can see, in fact there is nothing difficult about connecting the router to a computer via a network cable or a laptop via wifi - any beginner can do this!
FOR UPDATE
IMPORTANT: To avoid problems when updating the software, please read the following information about the update procedure.
- Check that the hardware version and software version match. Installing the wrong software version may damage your device and void your warranty. (Usually V1.x =V1)
It is NOT recommended to install a software version that is not intended for your region. Click here to select your region and download the most current software version.
- DO NOT turn off the power during the update process as this may damage the router
- Do NOT update your router software over Wi-Fi unless this is the only way.
- It is recommended that all users stop using all Internet applications on the computer or disconnect the network cable from client devices before updating.
Application for WiFi adapter TP-Link
Now let's talk about the TP-Link utility, developed for connecting a Windows PC to the Internet via wifi using an adapter from this company. It also comes bundled with the device on disk, or can be similarly downloaded from the official website.
After installation on your computer, a window will open with a selection of wifi networks available for connection. Select your router and enter the authorization key for the wireless signal
If your model has a TP-Link adapter in access point mode, you can also use it to distribute the Internet to other devices
TP-Link Update Frequently Asked Questions
When is the best time to update TP-Link drivers?
In order to get the full functionality of your TP-Link hardware, we recommend periodically checking for driver updates.
TP-Link Wireless Range Extender drivers serve as which utility?
Drivers are small programs that enable the operating system to properly communicate with the TP-Link Wireless Range Extender by acting as a means of "talking".
How to update TP-Link drivers?
TP-Link drivers can be updated manually using Windows Device Manager or automatically using a driver update tool.
What is the operating system compatibility for TP-Link drivers?
TP-Link currently has device drivers for Windows.
What if the TP-Link utility does not see the wifi adapter?
It happens that the TP-Link utility installed on the computer does not see the wifi adapter. In 99% of cases this happens because the drivers were not installed. The fact is that drivers and the utility are two completely different things. Although most often the adapters are recognized in the Windows system immediately after being connected to the USB connector, it is better to install both.
If you don’t have a CD, then to download drivers from the Internet go to the same TP-Link website and search for your model by adapter number
Just like with the router, select the device revision
And download the latest version of drivers for Windows
Downloading the firmware and preparing for the update
First of all, we need to download new firmware. If you don’t know if there is a new version for your router, then you can go to its settings, and immediately on the main page it will be indicated “Firmware version” (the very first line).
As for the OpenWRT and DD-WRT firmware, they seem to be available for these models. But, I would not recommend flashing. And everything works well on the native firmware. In any case, those who want to install OpenWRT, or DD-WRT, and know why, will understand this issue without any problems. And if you don’t know how to install this software, then you don’t need it.
How to find out the firmware version of a TP-Link router?
At the first stage, you need to find out what firmware is installed on your router and its hardware version. You will use this information as a starting point when choosing new software for your device. The hardware version is indicated on the router sticker located on the bottom side. On it you can see the serial number of the router and the version indicated in the form Ver: “value” (example: Ver: 4.0 ), or indicated by the last two characters next to the serial number:
If, for some reason, you cannot determine the hardware version on the sticker, then you can find it out through the WEB interface, where at the same time you will find out the software version. To get to the WEB interface, you will need to enter IP 192.168.0.1 , or enter the address https://tplinkwifi.net. After going to the IP address or domain name, an authorization window will appear on the screen (example):
The default login values are “admin” and “admin” , unless they have been changed previously. After completing authorization, you will be taken to the management page for your device. To find out the information you need, go to the “System Tools” and select “Firmware Upgrade” (the update page that you will need at the last stage), or the “Status” (router status):
Key Features
- The utility is in English, but there are no difficulties in using it;
- automatically finds the device and scans the network status;
- provides complete information about the wireless connection;
- you can create profiles for automatic connection;
- eliminates the possibility of failures and disconnections during Wi-Fi connections.
Download16.4 MB (downloads: 3107)Update date: 11/30/2018Russian language: NoDeveloper: TP-LINK Technologies Co., LtdWindows version: XP, Vista, 7, 8, 10 Similar programs
Mail.Ru Agent—Using the program, users can create separate groups and correspond with friends in a private chat, exchange files and videos. 3.53.5Canon MF Toolbox—The utility automatically detects the scanner connected to the PC. The main goal is to speed up the scanning process. Vidalia Bundle—The main goal is to make it impossible to track a user on the Internet. The utility operates in conjunction with the Tor program. VueScan—The utility has a wide range of functions that simplifies the scanning process. Using the program, you can make changes to the shade of color negatives. Mz Ram Booster—The main task of the program is to clean the system of unnecessary files and increase the performance of the entire system. The interface is in English.MyPublicWiFi—The main task of the utility is to turn your PC into a Wi-Fi access point. All main parameters are displayed in the main program window.
Hello! Wi-Fi adapters often come with a separate disk with an application. In this article I will show the general principles of working with such a wireless connection setup utility from TP-Link. Let's see how to use it correctly, and also where you can download it if it is missing. Begin!
Content
Firmware via phone
Some device models support operation and configuration through the Tether mobile application. If you have such a model, then you should take advantage of this, because here everything will be easier and faster. If the application is not installed, then sometimes it is faster to update using the standard method than to search for information to see if your router is compatible with it, and then download it, install it and connect to the device.
On your phone, connect to the router’s Wi-Fi network and log into the application.
There are several sections on the bottom panel. Click on “Tools” and find the “System” section. Click on Firmware Update. You will be taken to the next window, click on “Update” and wait for the complete download and update.
After that, check the settings. If they are completely reset, then use the standard data from the router to log in. Go to “System Tools” – “Backup and Restore”, find the button there to download files. Specify the path to the file that was saved in the process and select it. Click on “Restore” and wait until all settings are restored from the backup. At this point, the flashing process is considered complete.
